Apple iPhone 12 Display, Battery, Charging Flex, Side Key & Full Parts Guide (A2172, A2402, A2403, A2404)
Apple iPhone 12 is the first 5G iPhone, the first iPhone with a flat-sided aluminium frame and MagSafe, and the first standard iPhone with a Super Retina XDR OLED display — and it is still one of the most-repaired iPhones on the bench in 2026, now that Apple has stopped selling it new — and it is already on the mobilelcdled.com finder as Apple iPhone 12 (A2172, A2402, A2403, A2404, panel type OLED). This guide covers the full phone: display, battery, charging flex, on/off (side key) strip, main board, long flex and body — so a shop or a buyer can check exactly what they are ordering before they pay. It also completes the iPhone 12 → 13 → 14 → 15 chain on this site: the iPhone 13, the iPhone 14 and the iPhone 15 already have their own guides, so the four generations can now be compared side by side.
iPhone 12, front and back, in Blue — the wide notch at the top of the screen, the flat aluminium sides and the two camera lenses in a straight vertical line on the back are how you tell it apart from the iPhone 13 (smaller notch, diagonal lenses) and from the iPhone 12 Pro (three cameras, stainless steel frame).
Most-searched keywords this article answers
iPhone 12 display price, iPhone 12 LCD replacement, iPhone 12 screen replacement, iPhone 12 original display, iPhone 12 OLED screen, iPhone 12 display A2172, iPhone 12 battery replacement, iPhone 12 battery 2815mAh, iPhone 12 charging port repair, iPhone 12 Lightning flex, iPhone 12 power button not working, iPhone 12 on off strip, iPhone 12 side key flex, iPhone 12 motherboard, iPhone 12 logic board, iPhone 12 back glass replacement, iPhone 12 aluminium body parts, iPhone 12 spare parts, iPhone 12 display compatibility, iPhone 12 vs 12 Pro display, iPhone 12 vs 13 display difference, iPhone 12 MagSafe screen.
Refresh rate: 60 Hz — no ProMotion on this model; the 120 Hz ProMotion display belongs to the Pro models, not this phone
Protection: Ceramic Shield glass on the front; True Tone and P3 wide colour
Notch: the front camera and Face ID sensors sit in the wide notch at the top of the screen. The iPhone 13 notch is about 20% smaller, so a replacement display must have the correct wide iPhone 12 notch, or the Face ID sensors will not sit right
Fingerprint: none — unlock is Face ID only, so there is no under-display fingerprint sensor to worry about when swapping the display
Full mobile specification
The full specification below is cross-checked against Apple's iPhone 12 technical specifications and the iPhone 12 spec page on GSMArena. Apple's own iPhone 12 specs page may redirect to the generic iPhone page now that the model is discontinued, so the GSMArena page is the live cross-check.
Types / variants — which iPhone 12 is which
Model numbers: A2172 (USA), A2402 (Canada, Japan), A2403 (International), A2404 (China, Hong Kong); internal identifier iPhone13,2 — all are the same phone for display and parts purposes; always confirm the exact model number before ordering a part
Storage + RAM types: 64 GB + 4 GB RAM, 128 GB + 4 GB RAM, 256 GB + 4 GB RAM — every iPhone 12 has 4 GB RAM, so storage size is the only difference between variants
SIM types: Nano-SIM + eSIM (most markets), dual Nano-SIM (China models); the USA model (A2172) also has mmWave 5G, while the other models are Sub6 5G only
Colours: Black, White, Red, Green, Blue, Purple — the back glass is colour-infused, so a back-glass replacement must match the colour
Launched: announced 13 October 2020, released 23 October 2020; discontinued 12 September 2023, when the iPhone 15 series launched
Software: iOS 14.1 at launch, upgradable to newer iOS versions
Processor details
Chipset: Apple A14 Bionic (5 nm) — the first 5 nm chip in a phone, and the same chip family as the iPhone 12 Pro
Note for buyers: the A14 is fast enough for everyday use in 2026, but Apple Intelligence is not supported on this model — it needs an iPhone 15 Pro or later
For repair: the processor is soldered on the logic board, so a processor fault is a board-level repair, not a part swap
RAM and storage details
RAM: 4 GB in every variant — the same 4 GB as the iPhone 11, and less than the 6 GB in the iPhone 12 Pro
Storage: 64 GB, 128 GB or 256 GB, NVMe fast storage
No memory card slot: storage cannot be expanded, so a buyer choosing a used iPhone 12 should check the storage size first, because it cannot be changed later — and the 64 GB base model fills up fast
Charging type details
Wired charging: Lightning, USB 2.0, PD 2.0 — up to 50% charge in 30 minutes with a 20W adapter or higher (sold separately)
Wireless charging: 15W MagSafe, 7.5W Qi; 15W Qi2 after the iOS 17.4 update — the iPhone 12 is the first iPhone with MagSafe, the magnetic ring on the back that snaps chargers and wallets into place
Port: Lightning — the iPhone 15 moved to USB-C, so a USB-C flex does not fit this phone and a Lightning flex does not fit the 15
In practice: a weak or wrong charge-port flex will never deliver full fast-charging speed even with the right charger, and a Lightning flex from another iPhone model does not fit — the iPhone 12 flex is model-specific
Camera details
iPhone 12 rear dual cameras in Black — the two lenses sit in a straight vertical line in the square camera module, with the flash to the right of the lower lens and the microphone hole to the right of the upper lens. That straight-line layout is the quickest visual check that a phone (or a back glass) is an iPhone 12 and not an iPhone 13, which moved the lenses to a diagonal layout.
Rear video: 4K at 24/25/30/60 fps, 1080p at 25/30/60/120/240 fps, HDR, Dolby Vision HDR (up to 30 fps), stereo sound recording; dual-LED dual-tone flash, HDR (photo/panorama)
Front camera: 12 MP wide, f/2.2, 23mm, 1/3.6-inch sensor, 1.0µm pixels, plus the SL 3D depth/biometrics sensor for Face ID; video 4K at 24/25/30/60 fps, 1080p at 25/30/60/120 fps, gyro-EIS; HDR
Night mode: the first standard iPhone with Night mode on both the wide and the ultra-wide cameras, and Deep Fusion on all cameras
For repair: the two rear lenses sit in a straight vertical line in the square camera module — that straight-line layout is the quickest visual check that a phone (or a back glass) is an iPhone 12 and not an iPhone 13, which moved the lenses to a diagonal layout. A cracked lens glass is a back-glass job; a faulty lens itself means the camera module needs attention, not just the glass
Sound details
Loudspeakers: stereo speakers — one speaker at the bottom, one in the earpiece
3.5mm headphone jack: none — audio is via Lightning, Bluetooth 5.0 (A2DP, LE) or wireless earbuds
Other connectivity: Wi-Fi 6 (802.11 a/b/g/n/ac/6, dual-band, hotspot), NFC, Ultra Wideband (UWB), GPS / GLONASS / GALILEO / QZSS; no FM radio
Sensors: Face ID, accelerometer, gyro, proximity, compass, barometer; the first iPhone with 5G
Display / LCD — front side and back side pictures
A replacement iPhone 12 display is sold as a full assembly (panel with touch, flex cables and the wide-notch sensor area at the top). It is also sold with frame and without frame. Both are the same 6.1-inch Super Retina XDR OLED panel; the fitting work is different, so always confirm which one a seller is quoting — and always confirm the listing says "iPhone 12" (A2172 / A2402 / A2403 / A2404), not just "12 Pro" or "12 mini". The same assembly is also sold as "iPhone 12 / 12 Pro" — that is correct, because the two models share this display (see the finder section below).
iPhone 12 OLED display assembly — left: front side of the panel, screen off, with the wide notch at the top; right: back side, showing the shielding, the flex cables and the earpiece and Face ID sensor area at the top. Soft OLED and hard OLED panels are both sold for this model — confirm which grade a seller is quoting.
If you need the iPhone 12 display, contact us through our Contact page for price and availability.
What the compatibility finder says — honestly
As of this draft, the finder lists ONE compatible model for the iPhone 12 — a strong link, not a (verify) flag:
Compatible: iPhone 12 Pro — STRONG link. The iPhone 12 and the iPhone 12 Pro share the same 6.1-inch Super Retina XDR OLED panel (1170 x 2532, ~460 ppi) and the same display assembly, so the finder links them with no (verify) flag. The two phones differ elsewhere — the Pro has a stainless steel frame instead of aluminium, a third camera and LiDAR, and 6 GB RAM instead of 4 GB — but the display is the same part, which is why replacement screens are sold as "iPhone 12 / 12 Pro". The battery is shared too: both phones use the same 2815 mAh battery.
NOT compatible: iPhone 12 mini. The mini is a 5.4-inch phone with a 1080 x 2340 panel — smaller screen, smaller body, different display.
NOT compatible: iPhone 12 Pro Max. The Pro Max is a 6.7-inch phone with a 1284 x 2778 panel — bigger screen, bigger body, different display.
NOT compatible: iPhone 11. The iPhone 11 is the same 6.1-inch size on paper, but it has an LCD panel (828 x 1792) instead of OLED, a different flex and a different body — an iPhone 11 panel does not fit an iPhone 12.
NOT compatible: iPhone 13. The iPhone 13 is the closest look-alike — same 6.1-inch size, same 1170 x 2532 resolution — which is exactly why sellers group them. But the 13 has a notch about 20% smaller, a different display flex and a different earpiece/sensor layout. Do not fit an iPhone 13 panel in an iPhone 12 on a seller's word alone.
NOT compatible: iPhone 14. The iPhone 14 is the same 6.1-inch size and the same 1170 x 2532 resolution again, but it has a different display flex and earpiece layout — same size on paper, different part in the hand.
Battery is model-specific too — except the 12 Pro. The iPhone 12 battery is 2815 mAh, shared with the iPhone 12 Pro only. Do not fit a battery from the 12 mini, 12 Pro Max, 11, 13 or 14 on the strength of a similar size — match the model, not just the capacity.
Before ordering an iPhone 12 panel, search the exact model on mobilelcdled.com and check the compatibility list, rather than trusting a seller listing that groups every "12" model together.
Full parts details
1. Battery — 2815 mAh
iPhone 12 replacement battery — the black Li-ion cell is labelled "Rechargeable Li-ion Battery A2479", 3.83V, 10.78Wh and 2815mAh, with the connector tab on the side.
Capacity: 2815 mAh typical (10.78 Wh), Li-ion, 3.83V — the same battery as the iPhone 12 Pro, and smaller than the iPhone 13 battery (3240 mAh)
Charging: wired PD 2.0, up to 50% in 30 minutes with a 20W adapter or higher; 15W MagSafe, 7.5W Qi, 15W Qi2 (after iOS 17.4)
Signs it needs replacing: battery health dropping under 80% in Settings, phone switching off at 20–30%, battery draining fast, or the back glass lifting from a swelling battery
Warning: a swollen battery must not be punctured or bent — replace it, do not keep using it. On iPhones the battery is glued in with pull-tabs; a battery swap also needs the battery health to be re-paired, or iOS may keep showing the old health figure.
Part number note: the battery label in the photo reads A2479, 3.83V, 10.78Wh, 2815mAh — that is the number printed on the cell itself, so match the label and the model when ordering.
If you need the iPhone 12 battery, contact us through our Contact page for price and availability.
2. Charging flex / Lightning charge port flex
iPhone 12 Lightning charge port flex — the long flex assembly carrying the purple Lightning port at the bottom, with the microphone and antenna connections and the ribbon tail that runs up to the logic board. The flex in the photo is printed 821-02627-A.
What it is: the long flex assembly at the bottom of the phone carrying the Lightning charging port. It connects up to the logic board and carries charging, USB data, microphone and antenna signals.
Signs it is faulty: phone not charging, charging only at one cable angle, loose Lightning port, microphone not working on calls, or fast charging never kicking in even with the right charger
Fitting note: the charging flex is model-specific to the iPhone 12 — a Lightning flex from the 12 mini, 12 Pro Max, 11, 13 or iPhone 14 does not fit, even though the ports sit in the same place and look the same. The flex is also sold in colour-matched variants for the frame — match the model and the colour, not just the port shape.
Part number note: the flex in the photo is printed 821-02627-A — that is the marking on the part itself, so match the photo and the model when ordering, not a number from a listing title.
If you need the iPhone 12 charging flex, contact us through our Contact page for price and availability.
3. On / off strip — power button cable (side key flex)
iPhone 12 power and volume button flex cable — the long black flex with the metal side-button brackets, the volume buttons on one end and the power/side button on the other, with the connector that plugs into the logic board. The flex in the photo is printed 821-02539-04.
What it is: the power (on/off) and volume button cable — a long flex strip with the metal brackets that hold it against the frame buttons, plus the antenna contacts that run along the side of the phone.
Difference between listings: some sellers list the power button cable on its own and some list power and volume together as one assembly (shown above) — match the photo of the cable you are replacing before ordering, and order by model, not by a guessed number.
Signs it is faulty: power button not working, phone restarting when the button is pressed, volume buttons not working, or no click feeling from the side buttons
Fitting note: this is a long, thin flex — it tears easily if pulled at an angle. Fit it with the frame buttons aligned first, then press the flex down, never the other way round.
Part number note: the flex in the photo is printed 821-02539-04 — that is the marking on the part itself, so match the photo and the model when ordering, not a number from a listing title.
If you need the iPhone 12 power button flex, contact us through our Contact page for price and availability.
4. Main board (logic board)
iPhone 12 logic board — the L-shaped board with the large "A14" chip outlined in red, and the Qualcomm 5G modem chips outlined in yellow and green. The top half is one side of the board, the bottom half the other.
The board carries the cameras, SIM/eSIM, 5G modem, Wi-Fi 6, Bluetooth 5.0, UWB and the display/battery/charging connectors — so a board fault can look like a display, charging or network fault. Check the flexes and connectors first; they are cheaper than a board.
Board-level repairs (no signal, no power, water damage) need a specialist — a board swap also changes the phone's identity, so data and IMEI checks matter before ordering one.
Part number note: no logic-board number was verified for this draft, so none is printed here — do not order by a guessed number.
If you need the iPhone 12 main board, contact us through our Contact page for price and availability.
5. Long flex (interconnect flex) and LCD flex — do not mix them up
Long interconnect flex: on this iPhone there is no separate Samsung-style long flex between two boards. The job is done by the Lightning charge port flex (section 2 above) — the long flex that runs from the bottom of the phone up to the logic board. It carries charging, USB data, microphone and antenna signals. If it is damaged, the phone may stop charging, lose signal, or show a dead microphone — even though the Lightning port itself looks fine.
LCD flex: the short flexes on the back of the display itself, visible in the display photo above. They carry the picture and touch signals from the display to the logic board. A torn display flex means lines, no touch, or a black screen, and it usually means replacing the whole display assembly, not just the flex.
Rule for ordering: "long flex" = the Lightning charge-port flex from the bottom of the phone; "LCD flex" = the flex attached to the screen. Sellers sometimes list them under each other's names, so match the picture, not just the title.
Part number note: no long-flex or LCD-flex part number was verified for this draft, so none is printed here — do not order by a guessed number.
If you need the iPhone 12 long flex or display flex, contact us through our Contact page for price and availability.
6. Body details — frame, back glass, size and weight
iPhone 12 back glass housings — left to right: Purple, Blue, Green, Red, White and Black, shown from the inside with the metal plate and the MagSafe coil area, and the finished black back glass on the right with the dual-camera cutouts.
Size: 146.7 x 71.5 x 7.4 mm; weight: 164 g
Frame: aluminium — flat sides with the squared-off shape that came back with the iPhone 12, much lighter than the stainless steel frame of the 12 Pro
Front glass: Ceramic Shield; back: colour-infused glass, with the MagSafe magnetic ring built in
Water resistance: IP68 (up to 6 m fresh water for 30 minutes) — this rating is lost once the phone has been opened unless new adhesive seals are fitted
Colours: Black, White, Red, Green, Blue, Purple — the back glass is colour-infused, so a back-glass replacement must match the colour
Camera module: the two rear lenses sit in a straight vertical line in the square camera module — the quickest visual check that a phone (or a back glass) is an iPhone 12 and not an iPhone 13, which moved the lenses to a diagonal layout
If you need the iPhone 12 back glass or body parts, contact us through our Contact page for price and availability.
Why this matters for repair
The iPhone 12 is one of the most-repaired iPhones on the bench, so a wrong fitment is a costly return. Its 6.1-inch Super Retina XDR OLED panel, wide notch and Face ID sensor window mean the replacement must be the exact A2172 / A2402 / A2403 / A2404 panel — not a look-alike from the iPhone 13 (same resolution on paper, but a smaller notch and a different flex) or the iPhone 14 (same size again, different flex), despite the same screen size on paper.
The one safe swap is the iPhone 12 Pro: the finder lists it as a strong compatible model, because the two phones share the same display assembly and the same 2815 mAh battery. Everything else in the 12 family — mini, Pro Max — and the 11, 13 and 14 are different parts.
Check the part on every part before fitting: battery 2815 mAh (not the iPhone 13's 3240 mAh); charging flex and side-key flex matched by photo and model, not by a guessed part number. The iPhone 12 still uses Lightning — the iPhone 15 moved to USB-C — so a USB-C flex from the 15 does not fit this phone either.
If a future model is confirmed to share this display, the finder — and this article — should be updated together, with the same (verify) honesty the site uses elsewhere.
Next articles in the same series (from the most-searched list)
iPhone 13 (the direct successor — same 6.1-inch size, but a smaller notch, a bigger 3240 mAh battery and diagonal cameras), iPhone 14 (the Lightning-port successor most buyers compare it with), iPhone 15 Pro Max (the 6.7-inch Pro Max with the 120 Hz ProMotion display and USB 3).